Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P1740 » CVT RE0F09B  
 
 
  CVT RE0F09B  
 

P1740 LOCK-UP SELECT SOLENOID VALVE

Description

  • Lock-up select solenoid valve controls lock-up clutch pressure or forward clutch pressure (reverse brake pressure).
  • When controlling lock-up clutch, the valve is turned OFF. When controlling forward clutch, it is turned ON.

DTC Logic

DTC DETECTION LOGIC

  

DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

NOTE:
If "DTC CONFIRMATION PROCEDURE" has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
With CONSULT-III

  1. Turn ignition switch ON.
  2. Select "DATA MONITOR".
  3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

RANGE : "D" or "N" position (At each time, wait for 5 seconds.)

With GST
Follow the procedure "With CONSULT-III".
Is "P1740 LU-SLCT SOL/CIRC" detected?
YES >> Go to Diagnosis Procedure.
NO >> Check intermittent incident. Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.

Diagnosis Procedure
1.CHECK LOCK-UP SELECT SOLENOID VALVE CIRCUIT

  

  1. Turn ignition switch OFF.
  2. Disconnect TCM harness connector.
  3. Check resistance between TCM harness connector F16 terminal 37 and ground.

  

Is the Inspection result normal?
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK HARNESS BETWEEN TCM AND CVT UNIT (LOCK-UP SELECT SOLENOID VALVE) (PART 1)

  

  1. Disconnect CVT unit harness connector.
  2. Check continuity between TCM harness connector F16 (A) terminal 37 and CVT unit harness connector F46 (B) terminal 13.

  

Is the Inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK HARNESS BETWEEN TCM AND CVT UNIT (LOCK-UP SELECT SOLENOID VALVE) (PART 2)

  

Check continuity between TCM harness connector F16 terminal 37 and ground.

  

Is the Inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK LOCK-UP SELECT SOLENOID VALVE
Check lock-up select solenoid valve. Refer to Component Inspection (Lock-up Select Solenoid Valve).
Is the Inspection result normal?
YES >> GO TO 5.
NO >> Replace transaxle assembly. Refer to See: Transmission and Drivetrain\Continuously Variable Transmission/Transaxle\Service and Repair\CVT RE0F09B\Transaxle Assembly\Exploded View.
5.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the Inspection result normal?
YES >> Replace TCM. Refer to See: Powertrain Management\Transmission Control Systems\Control Module, CVT\Service and Repair\CVT RE0F09B\Exploded View.
NO >> Repair or replace damaged parts.

Component Inspection (Lock-up Select Solenoid Valve)
1.CHECK LOCK-UP SELECT SOLENOID VALVE

  

Check resistance between CVT unit connector terminal and ground.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> Replace transaxle assembly. Refer to See: Transmission and Drivetrain\Continuously Variable Transmission/Transaxle\Service and Repair\CVT RE0F09B\Transaxle Assembly\Exploded View.